3M? Multi-Touch Chassis Display User Guide
13
3M Touch Systems, Inc. Proprietary Information – TS
D-37732 REV H
Connecting the Touch Display
CAUTION
You are cautioned that any change or modification to the equipment not expressly
approved by the party responsible for compliance could void your authority to operate
such equipment.
To connect the Multi-Touch Chassis Display:
1.
Turn off your computer. You should always turn off the computer before connecting
or disconnecting a device.
2.
Select either the DVI or VGA cable. Connect one end
of the video cable to the video
connector on the display. Connect the other end to the video card in your computer.
3.
Connect one end of the touch sensor cable (
either
USB or serial) to the LCD.
Connect the other end to an available port on your computer.
Note:
Do not connect
both
USB and serial cables to the display. Choose one o
r the
other.
4.
Plug the power brick into the display.
5.
Connect the power cable to an appropriate grounded power source.
Testing the Multi-Touch Chassis Display
Note:
The Multi-Touch Chassis Display has a power statu
s light and video controls
located on the back of the display. If enclosure space is tight and access is important, an
on screen display remote control (part number 30114) is an option.
Before testing your touch display, make sure all cables are connected properly. Be sure
to tighten all cable screws. After connection, turn
on the power switch located on the
back of the display.
To test that the display is working properly:
1.
Turn on your computer.
2.
Make sure the video image is displayed. If it is not, check the LED to ensure that the
display is not in power save mode (amber)
3.
Make sure the video image is centered within the screen area. Use the display
controls to adjust the image, if necessary.
You can adjust the horizontal and vertical position, contrast, and brightness to better suit
your video card and your personal preference. For additional details, refer to the
Adjusting the Video Display later in this chapter.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
C25-0629
DISPLAY VFD CUSTOM DVD
C28-0605
VFD CUSTOM DVD DISP MULTI
C28-0704
DISPLAY VFD CUSTOM DVD
C2D10120D
DIODE SCHOTTKY 1200V 2x5A TO-247
C2D20120D
DIODE SCHOTTKY 1200V 22A TO-247
C3D20060D
DIODE SCHOT 600V 20A ZREC TO247
C40-0701A
DISPLAY VFD CUST APPLIANCE
C40-1405
DISPLAY VFD CUST ELEVATOR
相关代理商/技术参数
C2256-5
制造商: 功能描述: 制造商:RYESON CORPORATION 功能描述: 制造商:undefined 功能描述:
C22584-000
制造商:TE Connectivity 功能描述:MOLDED PART - Bulk 制造商:TE Connectivity 功能描述:322A024-4-0-CS8161
C225-AG
功能描述:开关配件 CAP SNPFIT GRN PB
RoHS:否 制造商:C&K Components 类型:Cap 用于:Pushbutton Switches 设计目的:
C225FL11047G6
功能描述:共模滤波器/扼流器 Ultra-Broadband Conical Inductors RoHS:否 制造商:TDK 电感: 阻抗:35 Ohms 容差: 最大直流电流:0.1 A 最大直流电阻:1.5 Ohms 自谐振频率: Q 最小值: 工作温度范围:- 25 C to + 85 C 端接类型:SMD/SMT 封装 / 箱体:0302 (0806 metric) 系列:TCE
C225FL2935G6
功能描述:共模滤波器/扼流器 Ultra-Broadband Conical Inductors RoHS:否 制造商:TDK 电感: 阻抗:35 Ohms 容差: 最大直流电流:0.1 A 最大直流电阻:1.5 Ohms 自谐振频率: Q 最小值: 工作温度范围:- 25 C to + 85 C 端接类型:SMD/SMT 封装 / 箱体:0302 (0806 metric) 系列:TCE
C225FL3536G6
功能描述:共模滤波器/扼流器 Ultra-Broadband Conical Inductors RoHS:否 制造商:TDK 电感: 阻抗:35 Ohms 容差: 最大直流电流:0.1 A 最大直流电阻:1.5 Ohms 自谐振频率: Q 最小值: 工作温度范围:- 25 C to + 85 C 端接类型:SMD/SMT 封装 / 箱体:0302 (0806 metric) 系列:TCE
C225FL4338G6
功能描述:共模滤波器/扼流器 Ultra-Broadband Conical Inductors RoHS:否 制造商:TDK 电感: 阻抗:35 Ohms 容差: 最大直流电流:0.1 A 最大直流电阻:1.5 Ohms 自谐振频率: Q 最小值: 工作温度范围:- 25 C to + 85 C 端接类型:SMD/SMT 封装 / 箱体:0302 (0806 metric) 系列:TCE
C225FL5740G6
功能描述:共模滤波器/扼流器 Ultra-Broadband Conical Inductors RoHS:否 制造商:TDK 电感: 阻抗:35 Ohms 容差: 最大直流电流:0.1 A 最大直流电阻:1.5 Ohms 自谐振频率: Q 最小值: 工作温度范围:- 25 C to + 85 C 端接类型:SMD/SMT 封装 / 箱体:0302 (0806 metric) 系列:TCE